About Us
PRODUCTS CENTER
Papua New Guinea NMEA 2000 N2k 5 Pin Micro Female Terminator 120-ohm
Premier Cable NMEA 2000 Approved Terminators allow for proper termination of an NMEA 2000 network. One male and one female terminator is required for each NMEA 2000 network.
Category:
Papua New GuineaNMEA2000 Cable Connector
Product Description
| Product Name | NMEA 2000 N2k Micro Female Terminator 120-ohm | |
| Key Words | NMEA2k N2K Network GPS Female 120 ohm Terminator NMEA 2000 Micro Termination Resistor Female Micro Termination Resistor Female N2K NMEA2000 Backbone Terminator NMEA 2000 Female Terminator N2k Terminating Resistor |
|
| Brand | Premier Cable , OEM | |
| Drawing # | PCM-0480 | |
| Pin Definition | CAN High, CAN Low, Power, Ground, and Shield | |
| Drop Line Connector | Micro-Change, M12 A-Coding, N2K Connector, Micro-C Connector, 5 Pin | |
| Trunk Line Connector | Mini-Change, 7/8" A-Coding, N2K Connector, Mini-C Connector, 5 Pin | |
| Cable Specification | (1 P*22#+ Free-edge-AL-MYLAR) + (1 P*24#+ Free-edge-AL-MYLAR) +D +B, HALF MATT PVC Resistance UV & OIL Resistance | |
| Certificate | UL, Rohs, Reach , NMEA2000 | |
| Compliance | Ratings IP67, IP68, Waterproof | |
| Compatible Brand | Lowrance, Garmin, Simrad Yachting, Actisense, Maretron, Ancor, Amphenol LTW, Molex, Mercury, Humminbird | |
| Description | The terminal resistor is an electronic component in the circuit. It is often used to adjust the input and output impedance of the circuit to prevent signal voltage fluctuations and reflections to ensure stable signal transmission. The role of the terminal resistor can be understood from the perspective of circuit transmission. In a circuit, signals need to be transmitted through cables or transmission media. When the signal is transmitted to the end of the transmission line, if there is no terminating resistor, part of the signal will be reflected back to the source end, which will produce echo and reflection interference. This reflection phenomenon will cause signal distortion, so that the amplitude and phase of the signal cannot be accurately received and decoded. The purpose of the terminal resistor is to solve this problem. By connecting the terminal resistor to the end of the transmission line, the signal can be completely matched between the transmission line and the terminal resistor, reducing or eliminating the impact of reflections. The terminal resistor can absorb the reflected signal on the transmission line, reduce the impact of echo and reflection interference, thereby maintaining stable signal transmission. |
|
| Communication Protocol | ||
| NMEA 0183, CAN/J1939，N2K protocol IEC 61162-3, Can Bus | NMEA2000，National Marine Electronics Association, Devicenet | Raymarine SeaTalk NG, Simrad SimNet, Furuno CAN, and Garmin NMEA 2000 |
| NMEA 2000 is compatible with the Controller Area Network，CAN Bus, it can be used for below Device Application | ||
| Gauge Instrumentation | Marine Navigation & Instruments | Marine sensors and display units |
| Gauge Panel Analog Gauge NMEA Voltmeter Gauge NMEA Fuel Level Gauge NMEA Tachometer Gauge NMEA Water Level Gauge NMEA Speedometer Gauge Marine Yacht Tank Gauge NMEA Oil Pressure Gauge Multiple Functional Gauge NMEA Water Temperature Gauge NMEA Holding Tank Level Gauge Digital Gauge NMEA 2000, CANBUS, J1939 |
NMEA 2000 Bridge J1708 Engine Gateway NMEA 2000 Thermometer GPS Navigation System NMEA 0183 Multiplexer NMEA 2000 USB Gateway NMEA 0183 Wi-Fi Router NMEA 2000 Wi-Fi Router NMEA 2000 Alarm Button NMEA 2000 Run Indicator NMEA 2000 Wi-Fi Gateway NMEA 0183 Wi-Fi Gateway NMEA 2000 Engine Gateway NMEA 2000 Switch Control NMEA 2000 Circuit Control NMEA 2000 Ethernet Gateway |
NMEA Buffer NMEA2000 Tank Gauge CX5001 NMEA2000 CX5003 converter NMEA2000 CX5016 converter NMEA 2000 Signal Converter NMEA 2000 Humidity Sensor NMEA 2000 Exhaust Gas Sensor CX5003 NMEA 2000 engine signal converter |